Underfloor heating in the Falkenberg municipality

Uneven underfloor heating is most often about flow rates and balancing. If some loops get too much flow they “take” the heat first, while other loops get too little and stay cool. It can feel like the heating is insufficient even though the real issue is distribution.

Another common cause is air in the system. Air pockets can block or slow circulation in a loop, causing cold spots and sometimes noise.

It can also be incorrect control: thermostats that open/close in a way that doesn’t suit the house, or a mixing group/supply that doesn’t deliver stable temperature.

We troubleshoot by measuring, checking flows at the manifold, bleeding air and adjusting so each loop gets the right conditions.

Signs that the system isn’t balanced are usually that some rooms get too warm while others never reach temperature. Many people notice they keep “chasing” the thermostats but still don’t get stable comfort.

Another sign is the heat source working harder than necessary: higher supply temperature than expected, short cycling, or a heat pump not running as efficiently as it could.

Underfloor heating is a low‑temperature system that works best with even flows and calm control. When flows are right, comfort improves — and you don’t have to keep adjusting settings.

We can review your system and perform balancing tailored to your home.

Yes, that’s common — especially in bathrooms, halls or kitchens during renovations. The key is doing it correctly with the right temperature for the underfloor loops, since underfloor heating typically needs lower supply temperature than radiators.

Often a mixing group or solution that gives the underfloor loops the right blended temperature is needed, so floors get warm without running the system too hot. The right setup also ensures underfloor heating doesn’t “steal” flow from radiators.

Control is also important: how the underfloor heating should be managed so you get stable indoor climate without the systems fighting each other.

We help plan a safe, working solution when you want to add underfloor heating.

It may be that the system isn’t delivering heat into the loops. Common causes are air in the loops, closed/faulty actuators/thermostats, or too low flow at the manifold.

In some cases the supply temperature is too low — for example if the mixing group is mis‑set, the heat pump isn’t set for underfloor heating, or control limits the temperature too much.

It can also be related to the floor build‑up and insulation. If the construction “leaks” heat downward or the floor covering dampens heat transfer, it can feel cool even when the system is working.

We troubleshoot focusing on circulation, temperatures and control — and help you find a fix that actually delivers warm floors.

The manifold is the hub of the underfloor heating system. Supply and return come in there, and heat is distributed to multiple loops — often one loop per room or zone. Manifolds usually have flow meters, valves and sometimes actuators controlled by thermostats.

It’s also where the system is balanced: you set how much flow each loop gets so rooms receive the right heat. Small adjustments can make a big difference in comfort.

If something is wrong — for example a loop gets no flow — the manifold is often the first place to check. You can see if flows are reasonable and if valves are working.

We can help both with manifold installation and with service/balancing of existing systems.

Underfloor heating is designed to run at lower temperatures than radiators. The exact temperature depends on the home’s needs, floor construction and loop layout, but the goal is often even heat with as low a supply temperature as possible.

Too high a temperature can make floors uncomfortably warm, dry the indoor air more and cause greater movement in some flooring materials. Too low, of course, gives poor comfort and cold surfaces.

With heat pump systems, low supply temperature is especially important for efficiency. That’s why balancing and correct curve settings are often just as important as the loops themselves.

We can help you find the right level and ensure the control runs steadily over time.

It can, especially with large temperature changes. Clicking often comes from materials moving as they heat and cool — floors, joists, pipes and fixings expand and contract.

Noise can also occur if pipes are too tightly fixed, if penetrations lack movement allowance, or if the system runs too hot and “forces” larger movements.

It could also be air in the system causing gurgling, or circulation issues creating a rushing sound.

We can assess whether the noise is normal for the construction or if something should be adjusted to reduce it.

The loops themselves rarely need “service” when installed correctly, but the system around them can: bleeding air, checking pressure, verifying actuators/thermostats, and ensuring the manifold is properly balanced.

If you have uneven heat, cold rooms or the system behaves oddly with weather changes, a check‑up can be well worth it. Often the cause is simple — and the fix makes a big difference.

In homes with heat pumps it’s also smart to view underfloor heating as part of the whole system. Correct flows and curve settings can improve comfort and stabilize operation.

We offer troubleshooting and service where we go through the system methodically and recommend the right fix.

Different floors conduct heat differently. Tile and stone transmit heat efficiently and often give quick, noticeable floor warmth. Wood and some laminates can dampen heat transfer, which may require adjustments in flow or temperature.

Thickness and build‑up also matter: a thick floor or an underlay that insulates can make the warmth feel weaker. At the same time, some materials require limited surface temperature to stay healthy.

That’s why it’s important to consider floor choice during installation so the system is sized and set up for the real conditions — not a “standard” assumption.

We can advise on what works best in your home and how to get good comfort with the covering you want.

Let us know whether it’s a new installation, an extension or troubleshooting. Describe the symptoms: which rooms are cold, is the heat uneven, do floors never get warm, or do they get too hot?

If you know: mention whether you have a heat pump, boiler or district heating, and if the underfloor heating is connected via a mixing group. Also mention if you have a manifold with flow meters and if thermostats/actuators control the rooms.

If there are noises (gurgling, rushing, clicking), say when they occur. That can say a lot about the cause.

Photos of the manifold, mixing group and any heat pump display/alerts often help us plan correctly and bring the right parts from the start.